Home > Printing News and Printing Knowledge > Printing knowledge: Types of Finishing - Binding 2/2

Printing knowledge: Types of Finishing - Binding 2/2

Published Time:2016-03-17 Original Source:printing products binding
Types of Finishes - Binding 2/2 1/2
Saddle Stitching
Saddle stitched books are constructed with sheets that are printed front and back that represent four pages of a book. The sheets of four pages are stacked with other sheets in the correct page order and then stapled along the fold line or saddle.
The stapling is accomplished on equipment that cuts staples from a continuous roll of wire mounted on the machine and inserts them into the paper. Some machines can do the folding and stitching in one operation. Many booklet manufacturers use this multiple task equipment to increase efficiency.
saddle stitch binding
 Saddle stitched binding can work for volumes up to 128 pages (32 sheets, printed with 2 pages front and back) if the paper stock is thin enough, but it just isn’t practical for anything larger. The larger the quantity of sheets, the greater the problem with a phenomenon called page “creep”.
Creep refers to the inner sheets sticking out further than those closer to the outside, because of the paper thickness. To compensate for this, the pages are “shingled”, which means that the inner margin, or “gutter”, is increased on the pages working from the inside of the book to the outside.
page creep 
Side Wire Stitching
Instead of staples being inserted into the side or saddle of the pages, staples are inserted into the top of the gathered sheets or pages and pressed down vertically until reaching the back side of the booklet. It is often used as a means to bind a larger quantity of sheets together than can be saddle stitched.
Side Wire Stitching 
Loop Stitching
Loop stitching is a form of binding where the stitches (staples) form a loop that can be used to hold the book in a binder (such as a standard 3 ring binder).
Loop stitching is basically the same method of binding as saddle stitching, however a special stitching head is used that produces a loop in the outside portion of the stitch. With this type of binding books can be put into binders without the need of drilling.
Loop Stitching 
Sewn Case Binding
Sewn case binding, also known as “edition binding”, is the most expensive binding method, but is the most durable. It can be used for any book thickness, but the most common thicknesses range from 1/4” up to 3”.
A number of steps are required to complete a sewn case bound book, so the process is very automated.
A large printed sheet containing 16 or 32 individual book pages, called a signature, is cut apart, folded, and assembled in the correct page order.
The signature is sewn together with other signatures.
Endleave papers, which are usually made of heavier stock than the other pages of the book, are glued to the outside of the first and last signatures.
The book is trimmed on three sides.
The sewn edge (spine) of the book is coated with glue.yellowprinting.com
The spine of the book is rounded in a machine to allow the cover of the book to function properly when it is attached.
A strip of gauze is wrapped around the spine of the book.
The cases (covers) that will be used for the book are made from heavy board stock with its grain running parallel to the spine of the book to prevent warping of the cover. The heavy board cases are wrapped with embossed paper, cloth, plastic coated material, leather, or other materials to form the final covering.
The book is attached to its hard case/cover on a casing-in machine, which glues the endleave papers to the case.
The final step is to insert the book into a hydraulic press to ensure that it dries properly and does not warp.
Sewn Case Binding Edition Binding
Sewn Soft Cover
Occasionally the pages of a book are attached to paperback or soft covers with the use of strong thread, which is sewn through the pages and cover using special equipment.
This binding method is often preferred for technical manuals and textbooks, which may be handled often by a number of people. It is more durable than perfect binding or wire binding where the overuse of a book may cause the binding to fail at a faster rate.
Sewn Soft Cover 
Common Cover Types
Two of the most popular types of covers used for saddle stitched booklets are the standard cover and the self cover.
cover types 
Some printed applications are padded into tablets or booklets with the use of an adhesive applied to one edge of a group of sheets.
Padding techniques are actually a form of binding, but the resulting pad or booklet is not intended to remain permanently bound – the padded edge serves only to keep the sheets together until a sheet is used and then detached from the padded edge.
Padding Binding 
Most of the padded products begin as single sheet items, which are then gathered and padded into various quantities to create note and memo pads, prescription pads, coupon pads, and many other similar applications.
The padding compound is usually a type of glue, which dries to a soft or semi-hard consistency. There are various types of glue used, such as varieties applied manually as a cold application and other varieties applied by machine as a hot melt application.
Note: Your vendor may have limitations on the number of sheets that can be padded as well as the minimum and maximum paper weights that can be manufactured into pads.
Cold Glue Application
The following steps are common for most padded applications using cold glue:
A large quantity of single sheets is stacked into a pile.
Chipboard or some type of heavy paper is inserted at designated intervals, which serves as a backer material and gives the pads stability.
The pile of sheets and pad backers are carefully jogged and precisely stacked to create a smooth edge for the application of the glue. The entire stack is jogged toward the side where the padding compound is to be applied.
A standard paintbrush is used to apply the glue to the stack of sheets.
After the glue is applied to the smooth edge of the stack, weight is applied to the top of the stack or the entire stack is clamped into a device called a padding press.
When the glue has dried, the weight or clamp is removed.
A knife is inserted into the large stack along the bottom of each piece of backer material in order to cut the glue and create the individual pads.
Hot Melt Application
For padded applications using hot melt adhesive, automated equipment speeds up the process. The circular or carousel padder is one of the most popular padding machines used for this type of application.
The following steps are typical for hot melt applications using the circular or carousel padding machine:
The single sheets are placed into stacks of 25, 50, 100 or an amount representing the quantity of sheets required per pad. Automated equipment is often used to count the sheets into the correct quantity per pad.
Each stack of sheets is combined with a backer sheet of chipboard or heavy paper.
The carousel padder has several identical clamping units, which pass by a staging area as the machine rotates. From the staging area, the operator inserts a stack of sheets, with a backer, into each clamping unit.
The clamping units have mechanisms that jog the single sheets and backer material into an even pile before the pad is clamped together.
The clamping units pass over a drum that applies the hot glue to the edge of the clamped pad. The hot melt glue dries very quickly after it is applied.
After a short interval, the clamping unit releases the pad, which falls onto a conveyor belt where it is retrieved and packaged.
These steps represent one revolution of the carousel machine. The speed of the carousel can be increased or reduced to accommodate the skill level of the operator in their ability to insert the pads into each clamping unit.
Note: Products padded with a hot melt glue and exposed to high temperatures in storerooms or car trunks, may develop a cracking or degumming of the adhesive causing the padded sheets to separate from the padding adhesive. Cracking or degumming of the adhesive will not occur with cold glue adhesives.
If you are looking for a Printing Company, try to contact Yellow Printing